How to Use an E6B: Wind Triangle and Groundspeed

To use an E6B for a wind triangle, enter wind direction and speed, true course and true airspeed to find wind-correction angle and groundspeed. Apply the correction to true course to obtain true heading, then handle magnetic variation and compass deviation separately. Use groundspeed—not indicated airspeed—for time over a ground distance.

By Sam Whitaker, Student PilotPublished · 8 min read
A tiny student adjusts a wall-mounted wind-computer model in a detailed sage-and-cream cutaway navigation room
A miniature navigation room illustrates learning a wind-computer setup; its unnumbered display provides no usable heading, weather or flight approval.
On this page
  1. Which E6B inputs and outputs should you know?
  2. Which side of a mechanical E6B does what?
  3. How do you set up the E6B wind side?
  4. What does the wind triangle show in this example?
  5. How do you turn WCA into a heading?
  6. How do you use groundspeed for time and fuel?
  7. What should you check in an electronic E6B?
  8. Check yourself
  9. Frequently asked questions
  10. Sources and review
  11. What should you practice next?

This guide works one hypothetical example on a conventional sliding-card mechanical E6B and checks the answer with vector arithmetic. Start with the aircraft performance hub for the broader planning framework.

Which E6B inputs and outputs should you know?

Keep air motion, ground motion and direction references separate.

QuantityMeaning in this guidePrimary reference
True course, TCIntended path over the ground, referenced to true northFAA PHAK Chapter 16
True airspeed, TASSpeed through the surrounding airPHAK navigation discussion
WindDirection it comes from and its speed; use the same north reference as courseFAA winds-aloft briefing guidance
Wind-correction angle, WCALeft or right heading adjustment to hold the coursePHAK wind triangle
Groundspeed, GSSpeed along the resulting ground trackPHAK Chapter 16
Planning contextTime, headings, TAS, groundspeed and fuel, including reservePrivate Pilot ACS, Task I.D

A wind-triangle solution is one planning input. It does not establish aircraft performance limits, fuel sufficiency, weather suitability or permission to fly.

Which side of a mechanical E6B does what?

The wind side solves the direction-and-speed problem; the circular slide-rule side handles ratios such as time, speed, distance and fuel rate.

This walkthrough uses the conventional sliding-card wind side described in the ASA E6-B manual. Circular-only instruments and electronic calculators have different controls. Follow the instructions for your particular model, especially its speed ranges and the value of each grid division.

Do not assume each line always means one knot or each angular division always means one degree. Identify the labels and scale before plotting. A well-placed mark on the wrong speed range gives a convincing but incorrect answer.

For the example, assume TC 090° true, TAS 120 knots, wind from 360° true at 20 knots. These are invented training inputs. TAS is supplied; 120 knots indicated is not an interchangeable input. In real planning, obtain TAS from the applicable aircraft performance data or a correctly performed conversion using the required atmospheric inputs.

How do you set up the E6B wind side?

Plot the wind first, rotate to course, then position the wind dot at TAS and read groundspeed at the centre.

Using the conventional ASA sliding-card method:

  1. Rotate the azimuth disc so 360°, the wind-from direction, meets the TRUE INDEX.
  2. Choose a convenient slide position. From the centre grommet, count 20 knots toward the index and make the wind dot. Use the model's actual scale.
  3. Rotate the disc to put 090° true course at the index.
  4. Move the sliding grid until the wind dot, rather than the grommet, lies on the 120-knot TAS arc.
  5. At the grommet, read approximately 118 knots groundspeed. The dot's angular position gives about 9.6° left WCA; a manual scale may support only roughly 10°.
Set wind and mark its speed, rotate to true course, then place the wind dot at TAS and read groundspeed at the grommet

Original setup reminder for a conventional sliding-card E6B, not a calibrated instrument face. Model-specific grid spacing and speed-range instructions still apply.

The dot represents the plotted wind displacement. Confusing the TAS location with the groundspeed readout is a common setup error. The start position used to mark wind speed is merely a convenient reference; the final slide position establishes the answer.

What does the wind triangle show in this example?

The airplane must point north of east so its northward air-relative motion cancels the wind's southward motion.

Wind from north moves air toward south. With the intended track east, the wind is from the left. A left correction therefore makes sense before reading any number. Right correction would increase the southward drift.

The original vector diagram shows how the motions combine. The blue air-relative vector has magnitude 120 knots. Its northward component is 20 knots, cancelled by the southward wind vector. The resulting ground vector points east.

A 120-knot air vector points north of east; a 20-knot southward wind leaves an eastward ground vector of 118.3 knots

Hypothetical, steady, uniform wind. Arrow lengths use the same speed scale; this is a velocity diagram, not a map, flight path or aircraft operating limitation.

The independent calculation is WCA = arcsin(20 ÷ 120) ≈ 9.6° left. True heading is 090° − 9.6° ≈ 080.4° true. Groundspeed is √(120² − 20²) ≈ 118.3 knots. Keep calculator angles in degrees.

Although the wind is perpendicular to the intended course, groundspeed is slightly below TAS because some airspeed is directed into the wind. Simply calling the result 120 knots would ignore that correction. The FAA's navigation chapter explains the distinction between heading, track and the combined air-and-wind motion.

How do you turn WCA into a heading?

Apply left or right WCA to true course first; true heading is not yet compass heading.

In this example, a left correction reduces 090° to about 080°. Use the side of the wind as a reasonableness check, while relying on the actual wind-triangle solution for magnitude.

StageThis hypothetical example
True course090° true
WCAAbout 9.6° left
True headingAbout 080.4° true, or roughly 080° on a manual solution
Magnetic headingNot calculated: local variation is not supplied
Compass headingNot calculated: applicable deviation is not supplied

Variation connects true and magnetic direction; deviation accounts for compass error in the airplane. Use the applicable variation and compass correction information with the correct signs. Do not insert an invented variation or call the true-heading result a compass heading.

Winds-aloft direction is referenced to true north in FAA briefing guidance. Surface radio voice reports can use magnetic direction, as the AIM explains. Check the actual source and electronic display rather than mixing a magnetic wind with a true course.

How do you use groundspeed for time and fuel?

Divide ground distance by groundspeed for elapsed hours, then multiply by the applicable fuel rate.

For a hypothetical 60-NM cruise segment at the unrounded example groundspeed:

  • Time: 60 ÷ 118.3216 ≈ 0.5071 hours, or 30.4 minutes.
  • With an assumed constant 8 US gal/hour, segment fuel is 8 × 0.5071 ≈ 4.06 US gal, rounded here to 4.1 US gal.

On the conventional slide-rule face, align the hourly index, commonly 60, with groundspeed on the outer scale. Opposite distance, read minutes on the time scale. For fuel, substitute the hourly fuel rate and read quantity against elapsed time.

At 118.3 knots, a 60-NM segment takes about 30.4 minutes and uses 4.1 US gallons at an assumed 8 US gallons per hour

Original arithmetic for one constant-speed cruise segment. It excludes taxi, climb, descent, contingencies and reserves; it is not a complete flight fuel requirement.

An E6B's repeated scale can represent different powers of ten. Estimate the size of the answer first: at nearly 120 knots, 60 NM takes about half an hour, not three minutes or five hours. Likewise, half an hour at 8 gal/hour uses about 4 gallons.

30.4 minutes is not 0.304 hours; divide minutes by 60. Keep nautical miles with knots, and match fuel quantity with the rate's unit. A US-gallon rate cannot be multiplied into a litre quantity without conversion.

91.103 requires the applicable preflight information, including weather, fuel requirements and alternatives for the flights described in paragraph (a). A segment calculation alone does not satisfy those broader planning needs.

What should you check in an electronic E6B?

Check the field meanings and output reference, then compare the answer with an independent estimate.

Enter true course, TAS, wind-from direction and wind speed in matching units and references. Read whether the result is WCA, true heading, magnetic heading or something else. Avoid entering IAS into a field asking for TAS, reversing wind-from into wind-to, or entering a heading when the field asks for course.

For these exact inputs, a compatible wind-triangle calculator should give approximately 9.6° left, 080.4° true heading and 118.3 knots GS. Small differences can follow input rounding or display precision; a right correction or a large speed disagreement needs investigation.

Recheck assumptions when actual conditions differ. A forecast is not a guarantee, and more decimal places do not improve a stale wind input. Cross-check progress and update planning using appropriate observations and procedures. The winds-aloft guide and preflight weather briefing checklist explain where the weather inputs fit.

Check yourself

With TC 090° true, TAS 120 knots and wind from 360° true at 20 knots, should the correction be left or right?

Show the answer

Left. Air moves south, so the airplane must point north of east to maintain the eastward course. The calculation gives about 9.6° left WCA, about 080.4° true heading and 118.3 knots groundspeed. A right correction would reinforce the drift instead of cancelling it.

After rotating to true course, which point goes on the TAS arc: the wind dot or the grommet?

Show the answer

On the conventional sliding-card method used here, the wind dot goes on the TAS arc. Groundspeed is read at the grommet. In this example that separates the 120-knot TAS input from the roughly 118-knot groundspeed output; follow your particular model's instructions and scale.

A 60-NM segment takes about 30.4 minutes at the example groundspeed. At 8 US gal/hour, is its cruise fuel about 2.4 gallons or 4.1 gallons?

Show the answer

About 4.1 US gallons: 30.4 ÷ 60 is approximately 0.507 hours, and multiplying by 8 gives about 4.06 gallons. Treating 30.4 minutes as 0.304 hours causes the smaller wrong result. This is segment consumption only, with reserves and other flight phases still unaccounted for.

Frequently asked questions

Do I enter indicated or true airspeed?

Use TAS for this wind-triangle problem. IAS describes a different quantity; obtain the appropriate TAS from aircraft data or a correct conversion. The hypothetical 120-knot TAS here is supplied directly, so no conversion is assumed.

Is the E6B heading automatically magnetic?

Not in the true-course setup used here. WCA applied to true course produces true heading. Variation and the applicable compass correction must be handled before calling a result magnetic or compass heading.

Why is groundspeed below TAS in a pure crosswind?

Holding course requires directing part of the air-relative velocity into the wind. Here 20 knots of northward air-relative motion cancels the southward wind, leaving about 118.3 knots eastward from the 120-knot TAS vector.

Does FirstSolo.ai approve my flight plan?

No. FirstSolo.ai is solely a study tool and does not issue FAA endorsements or flight approvals, now or in the future. Practice calculations support learning; real planning still requires current information, applicable aircraft data and the pilot's assessment.

Sources and review

Last reviewed November 11, 2026. Primary sources and all original example calculations were checked for this draft.

What should you practice next?

Return to the aircraft performance hub, then review the winds-aloft decoder and weather briefing checklist.

Practice cross-country planning on FirstSolo.ai. State the units, direction reference and expected correction side before accepting the readout. FirstSolo.ai supports study only and never issues endorsements or flight approvals.

About the author

Sam Whitaker, Student Pilot

Sam is a student pilot training in a Piper Warrior outside Denver, Colorado, fitting lessons around a full-time job. He writes up the practical side of the FAA written, from booking the test to what to bring on the day, with the FAA source for every rule.

Last reviewed Nov 11, 2026All guides by Sam

Keep going

Start here · PerformanceAircraft Performance: Private Pilot Guide
Practice this topic

A fresh question from the FAA references every time, graded by an AI DPE

Start with 50 free credits.

Start free