Pilotage and Dead Reckoning: A Student Guide
Pilotage and dead reckoning work together: dead reckoning predicts where you should be using direction, time, speed and wind, while pilotage checks that prediction against recognizable landmarks. Confirm checkpoints, compare actual arrival times with the plan, then revise groundspeed, ETA and fuel estimates. A calculation based on an uncertain position does not make that position certain.

On this page
- What is the difference between pilotage and dead reckoning?
- How do you choose checkpoints you can recognize?
- What should a dead-reckoning leg contain?
- How do you calculate a checkpoint’s expected arrival?
- How does a confirmed checkpoint update groundspeed?
- How do you revise ETA and fuel after the checkpoint?
- What if the checkpoint is missing or does not match?
- How should you practise this before a cross-country?
- Check yourself
- Frequently asked questions
- Sources and next steps
What is the difference between pilotage and dead reckoning?
Pilotage identifies position from landmarks; dead reckoning estimates position and progress from the flight’s starting information and motion.
The FAA PHAK’s navigation chapter, pages 16-12–16-13, describes them as complementary methods. The calculated heading and groundspeed predict the next checkpoint; recognizable features provide the observation used to check and update that prediction.
| Key fact | What it means | Source |
|---|---|---|
| Pilotage | Navigation by landmarks or checkpoints | PHAK 16-12 |
| Dead reckoning | Direction, time and speed, adjusted for wind | PHAK 16-13 |
| Leg time in minutes | Distance NM × 60 ÷ groundspeed kt | PHAK 16-11 |
| Observed groundspeed in knots | Distance NM × 60 ÷ elapsed minutes | PHAK 16-11 |
| VFR airplane day fuel minimum | First intended landing, then at least 30 minutes at normal cruising speed | 91.151(a)(1) |
| VFR airplane night fuel minimum | First intended landing, then at least 45 minutes at normal cruising speed | 91.151(a)(2) |
Formula source: PHAK Chapter 16. Fuel rule: 14 CFR 91.151, considering wind and forecast weather; these are airplane requirements, not a statement of sufficient planning margin for every flight.
Start with the sectional-reading guide for chart dates, airport information, terrain and airspace. The examples here use invented checkpoints and distances, not a route to fly.
How do you choose checkpoints you can recognize?
Choose prominent, distinguishable features and corroborate them with surrounding geography.
The PHAK’s pilotage section recommends features such as roads, rivers, railroads and lakes, with other features helping confirm their identity. A particular bridge at a river bend beside a road junction is more distinguishable than an unspecified bridge among several similar crossings.
Ask what the feature will look like from the intended direction and altitude, what nearby feature confirms it, and what recognizable feature brackets the route beyond it. Seasonal vegetation, haze, light, terrain and changes since chart publication can affect recognition. Do not assume every small road or structure is charted.
Choose useful checkpoints along the route rather than depending entirely on one. A checkpoint needs to support observation without drawing attention away from aircraft control, traffic and terrain. There is no universal spacing that guarantees a suitable visual route.
Original study framework. A bridge, river bend and road junction are illustrative recognition clues, not real locations, official chart symbols or a navigation procedure.
What should a dead-reckoning leg contain?
Record a known starting point, intended course, wind-adjusted heading, distance, groundspeed, time and appropriate fuel estimate.
The planned course describes the desired path over the ground. Heading is where the airplane points, and groundspeed determines progress over that path. Wind can make heading differ from course and groundspeed differ from true airspeed. The E6B wind-triangle guide explains those relationships.
Use current weather and aircraft-appropriate performance information. Keep nautical miles with knots, and convert minutes to hours when using an hourly fuel rate. Mark whether a time entry is leg duration or a clock time; mixing those two produces plausible-looking errors.
Establish the actual timing reference when the leg begins at its defined point. A takeoff time, a time passing a departure checkpoint and a time beginning a cruise segment are not automatically interchangeable. Account for climb, descent and other relevant phases in the complete plan rather than assigning cruise assumptions to the entire flight.
91.103 requires the pilot in command to become familiar with available flight information. For a flight away from an airport’s vicinity, that includes weather, fuel requirements and alternatives. A tidy navigation log is one aid to that work, not its completion.
How do you calculate a checkpoint’s expected arrival?
Divide leg distance by groundspeed, then add that duration to the leg’s starting clock time.
Suppose a fictional leg from A to B is 18 NM, with planned groundspeed 108 kt. The exercise starts at A at 14:00 UTC. These values are supplied for arithmetic; no aircraft, weather, heading or usable route is established.
Time = 18 × 60 ÷ 108 = 10 minutes. The planned arrival at B is 14:10 UTC. Use groundspeed rather than indicated or true airspeed unless the problem specifically establishes that they are equal.
Before identifying B, the time is a prediction. Passing a vaguely similar landmark at 14:10 does not prove it is B. Corroborate position from the chart and surrounding features before treating a crossing as an observed checkpoint.
How does a confirmed checkpoint update groundspeed?
Divide the known distance between confirmed points by the actual elapsed time, using consistent units.
In the same exercise, assume B is positively identified at 14:12 UTC, 12 minutes after A. Observed average groundspeed for A–B is 18 × 60 ÷ 12 = 90 kt. The airplane took longer than the predicted ten minutes, so its observed average groundspeed is lower than the planned 108 kt.
This result is an average over that segment. It does not, by itself, identify the wind vector, prove the airplane followed the intended track, or guarantee the same speed on a later leg. Check heading, track, timing and distance assumptions, then judge whether conditions justify using it for the next estimate.
Original fictional exercise. A and B are confirmed for this arithmetic; distance and time are supplied, and the result is an average groundspeed rather than a wind or heading solution.
Do not “correct” the clock to fit the plan. Record the observation, preserve the original estimate for comparison, and update the calculations that depend on it. If checkpoint identity or the timing reference is uncertain, retain that uncertainty instead of reporting precise-looking groundspeed.
How do you revise ETA and fuel after the checkpoint?
Recalculate the remaining leg from the actual checkpoint time and a justified groundspeed estimate.
Let the fictional next leg B–C be 27 NM. The original plan used 108 kt, so its duration was 15 minutes. Starting from planned B at 14:10, original C was 14:25 UTC.
For this exercise only, assume 90 kt remains appropriate for B–C. Its revised time is 27 × 60 ÷ 90 = 18 minutes. Starting from actual B at 14:12, revised C is 14:30 UTC.
| Scenario | Groundspeed | Leg duration | Checkpoint UTC |
|---|---|---|---|
| A–B, original 18 NM | 108 kt | 10 min | B: 14:10 |
| A–B, observed 18 NM | 90 kt average | 12 min | B: 14:12 |
| B–C, original 27 NM | 108 kt | 15 min | C: 14:25 |
| B–C, revised 27 NM | 90 kt assumed | 18 min | C: 14:30 |
C is now five minutes later than the original plan: two minutes already lost before B, plus three additional minutes on B–C. Merely adding the initial two-minute delay to the old C estimate would give 14:27 and miss the slower remaining leg.
If the exercise supplies a constant 8 US gal/hr for B–C, revised leg consumption is 8 × 18 ÷ 60 = 2.4 US gal, compared with the original 2.0 US gal. That invented cruise rate is not performance data for a real airplane.
Original fictional next-leg calculation. Constant speed and fuel rate are exercise assumptions; 2.4 US gal is leg consumption only, not total flight fuel or a reserve.
For actual planning, reassess remaining usable fuel, consumption and conditions using the applicable aircraft information. Include other flight phases, alternatives and appropriate margin. The airplane VFR reserve requirement in 91.151 is separate from calculated leg consumption; meeting an arithmetic estimate is not a guarantee of adequate fuel.
What if the checkpoint is missing or does not match?
Treat the position as unconfirmed and protect aircraft control while resolving the discrepancy.
Do not force an ambiguous landmark into the expected identity because its timing seems convenient. Compare the chart, last confirmed position, elapsed time, terrain and other available navigation information. Avoid an unplanned turn solely to chase a guessed feature.
The PHAK warns against relying on one checkpoint and explains why an unexpected heading change can worsen disorientation. Continuing a planned heading is not a universal instruction to continue toward a hazard; weather, terrain, airspace and fuel still govern the available choices.
If position uncertainty persists, seek appropriate assistance early and use applicable lost or diversion procedures. The Private Pilot ACS separately addresses lost procedures and diversion; a groundspeed formula cannot replace either. Keep an uncertain observation out of the “confirmed” column.
How should you practise this before a cross-country?
Practise a repeatable cycle: predict the next checkpoint, confirm it, compare actual progress, then update the plan.
Use an instructor-selected chart area to describe why each checkpoint is distinguishable, calculate leg times and explain how a changed observation affects ETA and fuel. Vary one assumption at a time. Keep original exercises separate from current flight planning.
ACS Task VI.A covers pilotage, dead reckoning, checkpoints, wind correction and comparing planned calculations with actual results. It also emphasizes managing distractions and maintaining aircraft control. For real preparation, pair the navigation work with the preflight briefing checklist.
Check yourself
A confirmed 18 NM leg takes 12 minutes. What is its observed average groundspeed?
Show the answer
90 kt: 18 × 60 ÷ 12 = 90. This uses nautical miles and minutes and describes the segment’s average groundspeed. It does not establish true airspeed, current wind, aircraft heading or a guaranteed speed for the next leg.
At actual B time 14:12 UTC, a 27 NM next leg is estimated at 90 kt. What is C’s revised ETA?
Show the answer
The leg takes 18 minutes, giving 14:30 UTC. That is five minutes after the original 14:25 plan, not just the two-minute delay at B. With the exercise’s 8 US gal/hr constant rate, this next leg consumes 2.4 US gal before any separate reserve or other flight phase is considered.
A bridge appears near the predicted time, but the expected river bend and road junction do not match. Can you use it as a confirmed checkpoint?
Show the answer
No. Timing alone does not establish its identity. Cross-check surrounding geography and other appropriate position information while maintaining aircraft control; retain uncertainty and seek assistance if needed. A precise calculation from an unconfirmed location is still based on uncertain position.
Frequently asked questions
Are pilotage and dead reckoning competing methods?
No. Dead reckoning predicts progress, and pilotage checks the prediction against recognizable features. Observations help update the heading, time and groundspeed assumptions rather than making one method unnecessary.
Should every checkpoint be a fixed number of minutes apart?
No single interval guarantees useful checkpoints. Choose prominent, distinguishable features that suit the route, conditions and workload, with enough supporting information to confirm them and recognize a missed feature.
Does the 2.4-gallon exercise result include required reserves?
No. It is only the fictional next leg’s consumption at the supplied constant rate. Actual fuel planning must account for the entire operation, conditions and applicable reserves and margins; the exercise does not establish a usable fuel quantity for a flight.
Can FirstSolo.ai approve the route or provide an endorsement?
No. FirstSolo.ai is solely a study tool. It does not issue FAA endorsements or flight approvals now or in the future. Use current official information, aircraft instructions and qualified instruction for real flight decisions.
Sources and next steps
- FAA PHAK Chapter 16: time/speed/distance, fuel, checkpoint selection and dead reckoning, especially pages 16-11–16-13.
- 14 CFR 91.103: preflight action and available flight information.
- 14 CFR 91.151: VFR airplane fuel requirements.
- Private Pilot Airplane ACS: Tasks VI.A, VI.C and VI.D.
Return to how to read a sectional chart, review E6B wind and groundspeed calculations, and connect the route with the preflight briefing checklist. Then practise pilotage and dead reckoning with FirstSolo.ai.

About the author
Sam Whitaker, Student PilotSam is a student pilot training in a Piper Warrior outside Denver, Colorado, fitting lessons around a full-time job. He writes up the practical side of the FAA written, from booking the test to what to bring on the day, with the FAA source for every rule.
Last reviewed Nov 17, 2026All guides by SamKeep going
Start here · NavigationHow to Read a Sectional Chart: Student Guide
Latitude and Longitude on a Sectional Chart
Read and plot coordinates, compare north/east position, and convert decimal minutes to seconds or decimal degrees with a worked study grid.
Sam Whitaker · Nov 20, 2026 · 8 min read
Magnetic Variation and Deviation: Heading Guide
Convert true, magnetic and compass headings with labeled examples, reverse checks and an aircraft compass-card reading exercise.
Ellie Navarro · Nov 18, 2026 · 8 min readA fresh question from the FAA references every time, graded by an AI DPE
Start with 50 free credits.
Start free